This website uses cookies to ensure you get the best experience on our website. Learn more

How to Hang a Kitchen Wall Cabinet | Ask This Old House

x

How to Hang a Kitchen Wall Cabinet | Ask This Old House

This Old House general contractor Tom Silva helps a homeowner purchase and install a kitchen wall cabinet. (See below for a shopping list, tools, and steps.)
SUBSCRIBE to This Old House:

Shopping List for Hanging a Kitchen Wall Cabinet:
- Kitchen wall cabinet [
- 3-inch cabinet screws [ used to fasten the cabinet to the wall

Tools List for Hanging a Kitchen Wall Cabinet:
- 4-foot level [ used to check for plumb and level alignment
- Stud finder [
- Drill/driver [
- Tape measure [
- Combination bit [ used to bore pilot holes
- Cabinet jack [ used to support the cabinet

Steps for Hanging a Kitchen Wall Cabinet:
1. Use a 4-foot level to see if the wall is plumb.
2. Mark the locations of the wall studs, then drill a small hole at each mark to confirm the stud locations.
3. Measure from a corner of the wall to the center of each stud, then transfer those dimensions to the back of the cabinet. Be sure to take into account the overhanging face frame.
4. Drill a pilot hole through the back of the cabinet at each stud location.
5. Reach inside the cabinet and hand-thread one 3-inch cabinet screw into each pilot hole.
6. Stand a cabinet jack in place below the cabinet location, then adjust the jack to the proper height.
7. Set the cabinet on top of the jack and press it tight to the wall.
8. Check the cabinet for level, then use a the drill to drive the screws through the upper back of the cabinet and into the wall studs.
9. Drill pilot holes and screw through the bottom of the cabinet, too.
10. Set a glass panel into each door and secure it with screw-on plastic clips.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Hang a Kitchen Wall Cabinet | Ask This Old House

How to Install Kitchen Cabinets | Ask This Old House

This Old House general contractor Tom Silva shares expert tips and techniques for installing new kitchen cabinets. (See below for a shopping list, tools, and steps.)
SUBSCRIBE to This Old House:

Shopping List for How to Install Kitchen Cabinets:
Kitchen cabinets [
3-inch screws [ to fasten cabinets to walls
Wood shims [ for leveling and plumbing cabinets
2x4 blocking [ to secure peninsula or island cabinets

Tools for How to Install Kitchen Cabinets:
2-foot [ and 6-foot [ levels, for determining level and plumb alignment
Tape measure [
Screwdriver [ to unscrew doors
Cordless drill [ for drilling holes
Impact driver [ to drive screws
Utility knife [ for trimming shims

Steps for How to Install Kitchen Cabinets:
1. Check the ceiling for level in two directions. If it’s out of level, find the low spot and use it as the measuring reference point.
2. Measure down from the ceiling (or low spot) 33 inches in several places and mark the walls. These marks represent the bottom of the upper cabinets.
3. Connect the marks with a long level and a sharp pencil to produce a level line along the kitchen walls.
4. Mark the stud locations on the walls, then measure and transfer stud locations to the back of the upper cabinets. (If you prefer to proceed with one cabinet at a time, begin with the one that will hang in the corner of the kitchen, and continue with consecutive cabinets.)
5. Pre-drill a screw-shank clearance hole through the cabinet backs at each stud location.
6. Unscrew and remove the cabinet doors; place the doors in a nearby room for safekeeping.
7. Hold the first wall cabinet in place in the corner of the kitchen. Be sure the bottom of the cabinet is even with the level line marked in Step 3.
8. Drive one screw through the upper back of the cabinet and into the wall stud.
9. Check the cabinet for plumb with a level. If necessary, slide shims behind the cabinet. Then drive in the remaining screws to secure the cabinet. Trim the shims with a utility knife.
10. Repeat the previous six steps to install the rest of the upper cabinets.
11. To prepare for installing the base cabinets, lay a 6-foot level on the floor in several places to identify the high spot.
12. From the floor’s high spot, measure up 34_ inches and mark the wall.
13. From that mark, draw a level line around the kitchen walls. This line represents the top of the base cabinets.
14. Install the sink base cabinet first, centering it under the window.
15. Drive shims under the sink cabinet, if necessary, to raise it flush with the 34_-inch reference line marked on the wall.
16. Fasten the sink base cabinet to the wall studs with 3-inch screws. Before fully tightening the screws, slip a shim behind the cabinet to fill any void.
17. Check the cabinet for level from front to back; slide shims under the front of the cabinet, if necessary, to level it. Trim the shims with the utility knife.
18. Install the remaining base cabinets in a similar manner.
19. To secure peninsula or island cabinets, screw 2x4 blocking to the floor. Set the cabinets over the blocking, then screw through the toekick and into the blocking.
20. Cover the exposed end of the cabinets with a decorative panel. Drive in short screws from inside the cabinet.
21. Install all the drawers and doors.
22. Fabricate a filler strip to fit alongside the base cabinet that abuts the range. Fasten the filler by screwing through the cabinet face frame.
23. Once the base cabinets are installed, make a template for the new countertop.

Watch new episodes of Ask TOH:

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Install Kitchen Cabinets | Ask This Old House
x

How to Install Kitchen Cabinets | This Old House

This Old House general contractor Tom Silva shows how to hang cabinets like a pro carpenter. (See below for a shopping list and tools.)
SUBSCRIBE to This Old House:

Shopping List for How to Install Kitchen Cabinets:
- kitchen wall and base cabinets [
- finishing nails [ used to find wall studs
- 3-inch drywall screws [ used to fasten filler strip to floor
- 1 1/4-inch pan-head screws [ used to screw sides of cabinets together
- wood shims [
- 2 1/2-inch drywall screw [ with finishing washer [ used to fasten rear of upper cabinets to wall
- cabinet jack [ used to hold wall cabinets

Tools for How to Install Kitchen Cabinets:
- 4-foot [ and 6-foot level [
- drill/driver [
- hammer [
- tape measure [
- clamps [ used to hold cabinets together
- jigsaw [ for cutting vent hole in over-the-stove cabinet

About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WETA Washington, DC.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Install Kitchen Cabinets | This Old House

How to Hang Crown Molding on Kitchen Cabinets | Ask This Old House

Ask This Old House general contractor Tom Silva installs crown molding on kitchen cabinets with full overlay doors
SUBSCRIBE to This Old House:

Time: 6 hours

Cost: $100

Skill Level: Moderate

Tools List for Hanging Crown Molding:
Brad nailer
Compressor
Drill driver
Miter saw
Caulking gun

Shopping List:
5/4” Pine
Fast drying spray primer
Super glue
Wood glue
Brad nails
Wood screws
Pencil
Wood putty
Paintable caulking

Steps:
1. Cut strips of the 5/4” pine to length and width, based on the size of the cabinets. These will be the filler pieces.
2. Make rabbet cuts on the filler pieces so that the piece fits tightly on the top of the cabinet and over the door of the cabinet.
3. Once the cuts are all made, spray paint the filler pieces to match the color of the cabinets in case they show through.
4. Mount the filler pieces to the cabinets using super glue to hold it in place and wood glue to more permanently bond it to the cabinet.
5. From the sides of the cabinet, nail the filler pieces in the place. For the front filler piece, drill from underneath the inside of the cabinet, and then secure that piece with wood screws.
6. Hold up the crown molding on the sides of the cabinet. Be sure they’re tight against the wall. Use a pencil to mark from the inside the correct measurement to cut the crown molding. Draw an arrow on the inside to help determine which angle the miter cut should go.
7. Hold the crown molding upside down and backwards so that it presses up safely against the fence of the miter saw. To keep it from slipping, you can use some of the clear polyurethane glue and a couple small pieces of wood to glue on the base of the saw to act as stops.
8. Turn the miter saw to 45 degrees based on the direction of the mark drawn on the crown molding during measuring. Cut the piece.
9. To make the sister cut on the opposite piece of crown molding, turn the saw to the opposite 45 degree angle and cut it again.
10. Nail the two pieces together using the brad nailer and then hold the crown molding back up to the cabinet to get the next measurement. Measure and mark the front piece of crown molding. Be sure to also mark the direction of the angle for the crown molding like before.
11. Make the miter cut for the front piece of crown molding. Then, make the sister cut for the following side like before.
12. Mount the crown molding to the cabinet using the brad nailer. Repeat this process with the rest of the cabinets with outside corners.
13. For any cabinets with an inside corner, cut the miters with the opposite 45 degree angle so that the miter angles on the crown molding cuts into itself.
14. Fill in all the nail holes with wood putty.
15. Caulk around the crown molding where it meets the ceiling to give it a finished look.

Resources:
The homeowner had already purchased shaker-style cabinets that came with the crown molding.

The wood glue and super glue Tom used for the crown molding and the filler pieces are both manufactured by Gorilla Glue (

The other materials Tom used to install the crown molding, including the brad nailer, compressor, and spray paint, are all found at home centers. For the spray paint, Tom recommends getting a fast drying spray primer with a dry time of one hour.

Expert assistance with this segment was provided by Universal Factory Direct (

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Hang Crown Molding on Kitchen Cabinets | Ask This Old House
x

Install Replace kitchen cabinets, By Yourself! Easy. Home Mender

The Home Mender, Dustin Luby, shows us how to install yourself new kitchen cabinetry. Click the links below to see inside Dustin's Toolbox. You can do it!
-Home Mender.

sweet Makita Cordless Drill

Ryobi Drill Bit set

Paslode Cordless Trim nailer


DISCLAIMER: This description contains affiliate links that help support the channel and if you click on a product link, The Home Mender channel receives a small commission. Actually, if you buy anything that day, we do. It allows us to continue to make new videos like this one. I personally choose all of these links to help build confidence in and to educate my audience.
Thank you ALL so much for your support! Let's get to it!

Don't Make This Rookie Mistake When Hanging Kitchen Cabinets

Leah demonstrates the importance of using the correct size screw when hanging cabinets...or risk piercing your electrical wires!

Check out Cabinets.com:

Support this channel by shopping on Amazon through our link:

If you like the work we do, consider supporting See Jane Drill on Patreon:

Contact Info:

Email Us: Leah@seejanedrill.com
Twitter:
Website:
Channel:
Facebook:

The opinions expressed in this video are those of Leah Bolden, and no other person nor entity.


Disclaimer:
Due to factors beyond the control of See Jane Drill, we cannot guarantee against improper use or unauthorized modifications of this information. See Jane Drill assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. See Jane Drill recommends safe practices when working with tools seen or implied in this video. Due to factors beyond the control of See Jane Drill, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not See Jane Drill.




#seejanedrill
x

Wall Cabinet Mounting Techniques

Remodel Your Own Kitchen! Visit:

Watch as a cabinet filler strip is added to a cabinet face and then fastened to the wall and adjoining cabinetry. Mounting or hanging cabinets is not hard to do, but there are few tricks to the trade that once learned make the project go a whole lot easier.

How To Install Upper Kitchen Cabinets By Yourself | THE HANDYMAN |

Here is the pole I use to install these cabinets
#thehandyman

How to Install a Simple Tile Backsplash | Ask This Old House

Ask This Old House General Contractor Tom Silva teaches a homeowner a simple technique for tiling backsplash.
SUBSCRIBE to This Old House:

Time: 2-3 hours

Cost: $100

Skill Level:
Beginner

Tools List for Installing a Simple Tile Backspash:
- Measuring tape [
- Scissors [
- Rubber float [
- Utility knife [
- Bucket [

Shopping List:
- Square tile [
- Tile adhesive mat [
- Pre-mixed grout [
- Degreasing cleaner [
- Drop cloth [
- Painters tape [
- Sponge [

Steps:
1. Clean the wall thoroughly with the cleaner to remove any grease or other debris.
2. Secure the drop cloth on the counter using the painters tape, covering the entire work area.
3. Mark the two sides of the wall using the painters tape where the backsplash should start and stop.
4. Measure the space you plan on tiling. Transfer the measurements to the tile adhesive mat and cut to size using scissors.
5. Peel one half of the back off of the adhesive mat, align the unexposed section to a straight surface like the existing countertop. Ensure the side with the thicker gap between glue dots is aligned to overlap the next sheet.
6. Once the sheet is in the correct position, stick it to the wall. Then peel the bottom half and stick that to the wall.
7. Repeat this process until the desired area is covered. Use the rubber float to push the adhesive mat to the wall for a permanent bond.
8. Hold the tile up to the wall to determine where it will need to be cut to size.
9. Use the utility knife to cut the mesh behind the tile.
10. Peel the plastic coating off of the adhesive mat, and carefully place each tile section onto the adhesive.
11. Once the tile is in the correct position, push it in place with a rubber float.
12. Repeat this process until the wall is covered with the tile.
13. Fill the gaps between the tile with the premixed grout and the rubber float. Apply it diagonally until all of the spaces between the tile have been filled with grout.
14. Fill the bucket with water and using a clean sponge, wipe the excess grout off the tile, again diagonally. Be careful to only wipe the grout off the face of the tile, not the grout in between the tiles.
15. After 24 hours, a haze may appear on the tile. To remove it, wipe the tile with a rag.

Resources:
To attach the tile to the wall, Tom used the SimpleMat tile setting mat, manufactured by Custom Building Proucts (

Tom installed Desert Sunset mosaic tile, manufactured by MS International (

The homeowner selected “Earth” colored premixed grout, which is also manufactured by Custom Building Products (

All of these, plus the other supplies and materials for this project, including razor knives, painter’s tape, and sponges, are sold at home centers.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Install a Simple Tile Backsplash | Ask This Old House

How to Add Kitchen Cabinet Storage | This Old House

This Old House general contractor Tom Silva explains how to add pull-out baskets, Lazy Susans, and more. (See before for a shopping list and tools.)
SUBSCRIBE to This Old House:

Shopping List for How to Add Kitchen Cabinet Storage:
- slide-out wire-rack basket, for under-sink storage
- slide-out wire-rack bin, for trash and recycling storage
- swing-out Lazy Susan rack, for blind-corner storage
- vacuum, used to clean out sawdust from inside of cabinets

Tools for How to Add Kitchen Cabinet Storage:
- cordless drill, used for drilling holes and driving screws
- reciprocating saw, used to cut out cabinet shelves
- jigsaw, used for modifying shelf to accept Lazy Susan storage rack

About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WETA Washington, DC.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Add Kitchen Cabinet Storage | This Old House
x

How To Install Kitchen Wall Cabinets - DIY At Bunnings

Kitchen wall cabinets are a wonderful way to increase storage space above the benchtop. In this video from Bunnings Warehouse on how to install kitchen wall cabinets you'll learn what tools you need for the job as well as some tricks of the trade for keeping the cabinets in place while you attach them to the wall.

For more DIY advice and information, visit the Bunnings website today:

How to Build a Wall-Hung TV Cabinet | This Old House

Senior technical editor Mark Powers and art director Douglas Adams demonstrates how to assemble and install a wall-hung TV cabinet. (See below for a shopping list and tools.)
SUBSCRIBE to This Old House:

Shopping List for How to Build a Wall-Hung TV Cabinet:
- Bifold door. Select a solid-wood bifold door. To determine the width you'll need, add about 4 inches to the width of your monitor and divide by 2. You'll need to round up to the nearest stock door size.
- 1x stock. Choose boards for the sides wide enough to span from the wall just past the face of the TV, as it protrudes from the wall. For the top and bottom, choose boards at least 2 inches wider than the side boards, to account for the thickness of the doors and the beveled overhang.
- 1x4s, to make the cleat and crosspiece. Get two 6-foot boards.
- Bifold door hinges, to join the halves of each door once you cut it down. Reuse the three that come with your doors and get one more.
- Flush-door H hinges, to attach the doors to the frame. Get four.
- 1 1/2-inch screws
- Magnet catches, made for cabinets. Get two.

Tools for How to Build a Wall-Hung TV Cabinet:
- Circular saw
- Combination square
- Speed Square
- Miter saw
- Drill/driver
- Countersink bit

About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WETA Washington, DC.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Build a Wall-Hung TV Cabinet | This Old House
x

Install or Hang Wall Cabinets (how to) - Renee Romeo

I will show you how to install or hang upper wall cabinets.
If you’d like to know how to install or hang upper wall cabinets, I am here to teach you. Typically, upper wall cabinets are hung in kitchens and laundry rooms. Today, I’m installing mine in the garage. I currently have a sink below the space where the cabinets will hang. I will cover Proper positioning for the new cabinets so that they look visually pleasing and so that people don’t bump their heads. There are industry standards that govern wall cabinet placement and I will cover that, as well.
Can I do this alone?

I will show you the secret to installing wall cabinets alone but I do have the help from my father today. He was around and it always makes the job easier to secure the first screw if there are more than two hands. Think safety! Some wall cabinets can be large and heavy, so don’t take the chance if you you don’t have to. I only required a few minutes of his time and then I finished the job by myself – you can too.
What do you need for this job? Wall cabinets in whatever size is necessary, a few simple tools and the proper fasteners to make a secure installation. I will take you through my project, step-by-step, and explain what I’m doing so that you can apply my methods to your own job. You will quickly and easily have storage behind closed doors. This is a must in a garage space where items quickly pile up and become eye sores. After you see my results, I will have you planning your next wall cabinetry project and your results will be just as good as mine. Best yet, this is an easy DIY project.

The DIY site that teaches you how to create and succeed with all projects around the home.

How to Add a New Dishwasher to a Kitchen | This Old House

Hooking up a new appliance with This Old House plumbing and heating expert Richard Trethewey. See below for a shopping list and tools.)
SUBSCRIBE to This Old House:

Shopping List for Adding a New Dishwasher to a Kitchen:
new dishwasher [
three-way shut-off valve [
stainless steel braided hose [
dishwasher tailpiece [
teflon tape [
polarized appliance plug [
electrical tape [

Tools List for Adding a New Dishwasher to a Kitchen:
adjustable wrench [
open-end wrench [
pliers [
drill/driver [
canvas tarp [

About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WETA Washington, DC.

Follow This Old House and Ask This Old House:
Facebook:
Twitter:

Pinterest:
Instagram:

Tumblr:

For more on This Old House and Ask This Old House, visit us at:

How to Add a New Dishwasher to a Kitchen | This Old House

How To Install Kitchen Cabinets On Concrete Brick Walls, Drywall

Today we'll show you how to install kitchen cabinets on concrete brick walls and you will do it yourself. The twist is that one wall is a standard interior stud wall behind drywall, and the adjoining wall is an exterior wall made from concrete brick blocks.

Tools and parts used in this video:
✅ Rockwell RK5151K Sonicrafter cut drywall:
✅ Grk 120660 White Cabinet Screw, 8 X 2-1/2:
✅ GRK Pro-Pak White Cabinet Screws, 8 x 1-1/2:
✅ Red Head Dynabolt 1/2-Inch by 4-Inch Sleeve Anchor:

✅ SUBSCRIBE:

✅ WATCH: How To Install Loose Mosaic Backsplash Tiles Falling Off Sheets


✅ WATCH PLAYLIST: Best DIY Kitchen Remodel Tips & Cabinet Installs


✅ WATCH: How to Install Kitchen Cabinets DIY Like Pros


How To Install Kitchen Cabinets On Concrete Brick Walls and Drywall

Hello DIY folks. Did you ever wonder how to Install Kitchen Cabinets on Exterior Cement Brick Walls? If you came here to learn How to hang kitchen cabinets on drywall, then you are in the right place.

How to hang kitchen cabinets on drywall

We'll focus a few minutes on wall prep and how to add wood cabinet blocking to your stud wall first to support the hanging kitchen cabinets. We show you best types of kitchen cabinet screws and concrete anchors to use to mount kitchen cabinets to drywall, or to mount kitchen cabinets to brick walls.

Installing kitchen cabinets

We'll also cover using a ledger board to ensure a perfectly level row of cabinets hanging on the wall. This video is a good learning experience for you because it shows you the same installation the challenges of mounting kitchen cabinets to drywall on one wall and hanging kitchen cabinets on concrete walls all in the same kitchen.

Installing kitchen cabinets on brick walls requires special 4 sleeve anchors as we explain in detail in the video, which will help you make hanging kitchen cabinets on brick walls a simple task.

We hope you like this how to kitchen cabinets video for installing kitchen cabinet son cement walls. Now you can take our DIY cabinets installation tips and create your kitchen cabinets makeover. Good luck as you hang kitchen wall cabinets. Now you can show your friends how to hang kitchen cabinets on drywall.
x

Cabinet Installation Tips

Contractor Mark Clement walks through his cabinet installation with SPAX Cabinet Screws while also explaining why SPAX is a true favorite on his job sites.

How to fit kitchen units part 1: assembling & fitting units

Update: Our HomeFit service will no longer be available from the 9 July 2018. Any existing orders will be honoured until 14 December 2018.

Even though it’s no longer available, we still offer a great kitchen, bathroom and bedroom range. We’d love to help design your dream room too, so visit your local store and speak to a member of our team.

Watch our step-by-step video showing how to fit kitchen units, with expert advice and top tips to help you complete the job with confidence.

See the other part in this series:
Part 2: Fitting Unit Doors & Handles


Visit the official B&Q YouTube channel. Here you'll find the ideas and know-how you need to make your home improvement dream a reality:

Need a helping hand with your DIY project? We're always uploading new videos, so whatever your project, we're here to support you 24/7. Subscribe today so you don't miss out.

For more advice go to
To shop at B&Q go to
Join the B&Q Club for exclusive offers:

Like us on Facebook:
Follow us on Twitter:
Be inspired on Pinterest:
Find new ideas on Instagram:

How to Install Kitchen Cabinets -- Buildipedia DIY

Read the full How-To:

With the right tools and a little patience, installing kitchen cabinets is a project any do-it-yourselfer can handle. Join host Jeff Wilson for tips on keeping things square and level as he installs new base cabinets for a small kitchenette.

Installing Kitchen Cabinets DIY, | How To Install Like Pros

Do you want to know How to Install Kitchen Cabinets Like Pros do for your kitchen remodel? In this DIY kitchen cabinet installation tips and tricks video we show you how to install cabinets, hanging cabinets, traditional kitchen cabinet installation methods with ledger boards as homeowners/DIY folks don't have cabinet installation tools like lasers for kitchen cabinet installation. Our kitchen cabinet installation tips and tricks DIY video gets you installing kitchen cabinets now. Enjoy our how to how to install kitchen cabinets on wall tips.

✅ Tools & kitchen cabinet screws in this how to install kitchen cabinets installation video:
✅ Precision Sensors Stud Finder LED Profinder:
✅ Grk 120660 White Cabinet Screw, to install cabinets 8 X 2-1/2:
✅ GRK Pro-Pak White Cabinet Screws, 8 x 1-1/2:
✅ DEWALT DCK299D1T1 Hammer Drill, Impact Driver Kit for installing cabinets:
✅ Empire Professional Framing Square:
✅ Johnson 72 Heavy Duty Aluminum Box Level:

✅ SUBSCRIBE:
For useful DIY kitchen remodeling tips, tricks for installing cabinets, subscribe here:

✅ WATCH: How To Add Cabinet/Wall Blocking To Stud Walls, Kitchen Cabinet Installation:

✅ WATCH: How To Install Kitchen Cabinets On Concrete Brick Walls Or Drywall:

✅ WATCH: Best Screws For Installing Kitchen Cabinets, Which To Avoid:

How To Install Kitchen Cabinets On Walls

Before you do it yourself and install cabinets, start with correct kitchen cabinet installation screws. We'll cover which kitchen cabinet installation screws you Do It Yourself folks should use and which kitchen cabinet fasteners to stay clear from while installing cabinets.

installing wall cabinets

This will help avoid errors in your kitchen cabinet installation. Follow our kitchen cabinet installation DIY tips, you'll have the perfect kitchen cabinet installation.

Best DIY tips for hanging cabinets on kitchen walls

If you are about to hang cabinets on walls It is crucial to follow our kitchen cabinet installation tips and tricks, especially with cabinet screws. Knowing which kitchen cabinet fasteners to use for your walls, prior to installing cabinets.

How to install kitchen cabinets

When you install cabinets, first fasten together the upper kitchen cabinets installation, hang cabinets on the wall on top of a ledger board, until you can use kitchen cabinet screws to fasten the wall cabinets to the studs. Once upper kitchen cabinets are installed, you can then start installing kitchen base cabinets.

How to Install Kitchen Cabinets DIY Like Pros Tips and Tricks

kitchen cabinet installation can be rewarding if you take your time, measure twice, cut once before installing cabinets, make sure all the kitchen cabinets are level, plumb, true, and front edges are all flush with one another.

Install kitchen cabinets

We also cover which cabinet installation tools you should use to install cabinets, and which cabinet screws and fasteners you should use when hanging kitchen cabinets in your cabinet installation project.

How to install cabinets in kitchen remodel

After you learn how to install kitchen cabinets on walls, we'll cover how to adjust kitchen cabinet doors, adjusting them left or right for perfect spacing between cabinet doors. Installing kitchen cabinets will be a breeze after watching this DIY kitchen cabinets video, you'll be ready to hang kitchen cabinets.

Installing wall cabinets is fun

We hope you enjoyed this how to kitchen cabinet installation video, now you are ready to install kitchen cabinets on walls like the pros. You'll be giving kitchen cabinet installation tips to your friends.
Now, show others how to start hanging kitchen cabinets, and installing wall cabinets. Thanks for stopping by our how to install cabinets video.

See Bill Connelly's channel, view his how to install kitchen cabinets video. This Old house has a decent how to install kitchen cabinets video, but it is short, leaving out details on installing kitchen cabinets on walls.

Lastly, see Dustin from Home Mender channel, with a useful DIY video on how to install kitchen cabinets, tou'll love his method of
installing kitchen cabinets. Home Mender kitchen cabinet installation DIY video is quick and easy to follow, but leaves out many detailed steps for installing kitchen cabinets DIY like if you discover the wall is warped. Home Mender's method of installing kitchen cabinets one at a time is not the best for do it yourself remodelers, but works if you work alone, have no cabinet installation tools, and have no one to help you installing cabinets.

If you follow this how to install kitchen cabinets on walls DIY video, installing cabinets will go well for you. When installing kitchen cabinets if you can get a 3rd person, that is better.

IKEA Upper Cabinet Install - How to Install Cabinets with Crooked Walls

If you have a house with corners that are out of square, out of plumb (or level if you want to call it that) or crooked and crowned then this video might help you figure out some methods on how to maintain an easy installation of your IKEA Kitchen. I also show you how this affects the lower cabinets especially when they need to line up. Example would be a fridge gable. Every scenario will be slightly different but I have more shorter IKEA videos packed full of Info. Along with these is a full 5 part series where I install a kitchen from start to finish.

Shares

x

Check Also

x

Menu